TKK_E32210409/kombinasi.ino

#define BLYNK_PRINT Serial
#define BLYNK_TEMPLATE_ID "TMPL6pmSmTWSq"
#define BLYNK_TEMPLATE_NAME "Sensor"

#include <ESP8266WiFi.h>
#include <BlynkSimpleEsp8266.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <DHT.h>
#include <DHT_U.h>
#include <Servo.h>

// Blynk authentication token and WiFi credentials
char auth[] = "RV_-8PWtIpIC09kAYSfGtZT6r6ezJNCk";  // Blynk auth token
char ssid[] = "realme 5 Pro";                      // Wi-Fi SSID
char pass[] = "tugasakhir";                        // Wi-Fi password

// Pin Definitions
const int servoPin = D6;        // Pin for the servo
const int mq135Pin = A0;        // Pin for the MQ-135 sensor
#define DHTPin D3              // Pin for the DHT sensor
const int relayPin = D4;       // Pin for the relay controlling the fan

#define VPIN_TEMP V0
#define VPIN_HUM V1
#define VPIN_UDARA V2           // Blynk virtual pin
#define VPIN_FAN V3
#define VPIN_SERVO V4

const int thresholdPPM = 65;  // New threshold for MQ-135 in PPM

// Servo Setup
Servo myServo;
int closedPosition = 0; // Position when window is closed
int openPosition = 90;  // Position when window is open

#define DHTTYPE DHT11
DHT dht(DHTPin, DHTTYPE);

LiquidCrystal_I2C lcd(0x27, 16, 2);  // Address 0x27, 16x2 LCD

unsigned long previousMillis = 0;  // Stores the last time data was sent
const long interval = 60000;       // Interval to send data (1 minute)

bool fanState = false;             // State of the fan
bool windowState = false;          // State of the window

void setup() {
  Serial.begin(115200);
  Serial.println("Connecting to Wi-Fi...");

  Blynk.begin(auth, ssid, pass);

  pinMode(relayPin, OUTPUT); 
  digitalWrite(relayPin, HIGH);   // Turn off relay initially

  myServo.attach(servoPin);  // Attach servo to the specified pin
  myServo.write(closedPosition);  // Initial servo position

  dht.begin();  // Initialize DHT sensor
  lcd.init();  // Initialize LCD
  lcd.backlight();  // Turn on LCD backlight

  Serial.println("Setup completed");
}

void loop() {
  Blynk.run();
  sensorReadings();

  unsigned long currentMillis = millis();
  if (currentMillis - previousMillis >= interval) {
    previousMillis = currentMillis;
    sendDataToBlynk();
  }
}

void sensorReadings() {
  int sensorValue = analogRead(mq135Pin);
  // Adding a delay to stabilize the readings
  delay(200); 
  sensorValue = analogRead(mq135Pin);
  int ppm = map(sensorValue, 0, 1023, 0, 500); // Adjusted range for MQ-135

  float h = dht.readHumidity();
  float t = dht.readTemperature();

  if (isnan(h) || isnan(t)) {
    Serial.println("Failed to read from sensor");
    return;
  }

  Blynk.virtualWrite(VPIN_TEMP, t);
  Blynk.virtualWrite(VPIN_HUM, h);
  Blynk.virtualWrite(VPIN_UDARA, ppm);

  Serial.print("Humidity: ");
  Serial.print(h);
  Serial.print("%\t");
  Serial.print("Temperature: ");
  Serial.print(t);
  Serial.print("°C\t");
  Serial.print("PPM: ");
  Serial.println(ppm);

  lcd.setCursor(0, 1);
  lcd.print("Temp: ");
  lcd.print(t);
  lcd.print("C");

  lcd.setCursor(2, 0);
  lcd.print("ppm: ");
  lcd.print(String(ppm));
}

void openWindow() {
  myServo.write(openPosition);
  windowState = true;
  Serial.println("Window opened.");
}

void closeWindow() {
  myServo.write(closedPosition);
  windowState = false;
  Serial.println("Window closed.");
}

void turnFanOn() {
  digitalWrite(relayPin, LOW);  // Turn on fan
  fanState = true;
}

void turnFanOff() {
  digitalWrite(relayPin, HIGH);  // Turn off fan
  fanState = false;
}

void sendDataToBlynk() {
  float h = dht.readHumidity();
  float t = dht.readTemperature();
  int sensorValue = analogRead(mq135Pin);
  int ppm = map(sensorValue, 0, 1023, 0, 500);  // Adjusted range for MQ-135

  if (isnan(h) || isnan(t)) {
    Serial.println("Failed to read from sensor");
    return;
  }

  Blynk.virtualWrite(VPIN_TEMP, t);
  Blynk.virtualWrite(VPIN_HUM, h);
  Blynk.virtualWrite(VPIN_UDARA, ppm);
  Blynk.virtualWrite(VPIN_FAN, fanState ? 1 : 0);
  Blynk.virtualWrite(VPIN_SERVO, windowState ? 1 : 0);

  Serial.print("Humidity: ");
  Serial.print(h);
  Serial.print("%\t");
  Serial.print("Temperature: ");
  Serial.print(t);
  Serial.print("°C\t");
  Serial.print("PPM: ");
  Serial.println(ppm);

  lcd.setCursor(0, 1);
  lcd.print("Temp: ");
  lcd.print(t);
  lcd.print("C");

  lcd.setCursor(2, 0);
  lcd.print("ppm: ");
  lcd.print(String(ppm));
}

// Blynk function to control the fan via button
BLYNK_WRITE(VPIN_FAN) {
  int fanControl = param.asInt();
  if (fanControl == 1) {
    turnFanOn();
  } else {
    turnFanOff();
  }
}

// Blynk function to control the servo via button
BLYNK_WRITE(VPIN_SERVO) {
  int servoControl = param.asInt();
  if (servoControl == 1) {
    openWindow();
  } else {
    closeWindow();
  }
}